High Torque Nema 23 CNC Stepper Motor 114mm 425oz.in/3Nm CNC Mill Lathe RouterSTEPPERONLINE #ad - 3nm425oz. In holding torque. Very Huge Torque. Rated current 4. 2a & resistance 09ohms. This is the strongest model for Nema 23 stepper motor, it with 1. 8 deg. Each phase draws 4. 2a, allowing for a holding torque of 3. 0nm425oz. In. Electrical specification: * manufacturer part Number: 23HS45-4204S * Motor Type: Bipolar Stepper * Step Angle: 1.
8 deg. Step angle 200 steps/revolution. Nema 23 bipolar 2. 24"x2. 24"x4. 45" 4-wire. Step angle200 steps/rev. 1. 8 deg. Connecting the motor directly to a power supply will destroy the motor. Holding Torque: 3. 0nm425oz. In * rated Current/phase: 4. 2a * phase Resistance: 09ohms * Inductance: 3. 8mh+/-20%1khz physical specification: * frame size: 57 x 57mm * body length: 113mm * shaft diameter: 10mm * Shaft Length: 24mm * D-cut Length: 20mm * Number of Leads: 4 * Lead Length: 400mm * Weight: 1.
STEPPERONLINE Nema 17 Stepper Motor Bipolar 2A 59Ncm84oz.in 48mm Body 4-lead W/ 1m Cable and Connector compatible with 3D Printer/CNCOSM Technology Co.,Ltd. 17HS19-2004S #ad - Important notice: some customers reported they bought this model from other sellers under this listing, but found much of difference with our descriptionno connector and shorter leads. 1. 8 deg. Electrical specification: * manufacturer part Number: 17HS19-2004S1 * Motor Type: Bipolar Stepper* Step Angle: 1.
STEPPERONLINE Nema 17 Stepper Motor Bipolar 2A 59Ncm84oz.in 48mm Body 4-lead W/ 1m Cable and Connector compatible with 3D Printer/CNC #ad - 8 deg. We highly recommend you report this problem to Amazon if you have same experience. If you are a new buyer, please pay attention that our id is "STEPPERONLINE", and our P/N is "17HS19-2004S1". 3nm425oz. In holding torque. 3d printer motor with high torque. Build with 39. 37" 1m cable and 01" pitch Connector. Nema 23 bipolar 2.
24"x2. 24"x4. 45" 4-wire. Rated current 2. 0a & resistance 1. 4ohms.
STEPPERONLINE CNC Stepper Motor Driver 1.0-4.2A 20-50VDC 1/128 Micro-step Resolutions for Nema 17 and 23 Stepper MotorOMC CORPORATION LIMITED DM542T #ad - Step angle200 steps/rev. Nema 23 bipolar 2. 24"x2. 24"x4. 45" 4-wire. 59ncm83. 6oz. In holding torque. Rated current 2. 0a & resistance 1. 4ohms. Key features: * anti-resonance provides optimal torque and nulls mid-range instability * motor auto-identification and parameter auto-configuration when power on, 1/20, 1/50, thus offers smoother motor movement * 15 selectable microstep resolutions: 1/2, 1/125, 1/4, offer optimal responses with different motors * Multi-Stepping allows a low resolution step input to produce a higher microstep output, 1/40, 1/100, 1/16, 1/25, 1/64, 1/10, 1/32, 1/8, 1/5, 1/128 * Soft-start with no "jump" when powered on * 8 selectable peak current including 1.
00a to 4. 20a * pulse input frequency up to 200 khz, ttl compatible and optically isolated input * Automatic idle-current reduction * Suitable for 2-phase and 4-phase motors * Support PUL/DIR mode * Over-voltage and over-current protections Electrical Specifications: * Output Peak Current: 1. 0~4. 2a 3. 0 rms * input voltage: +20~50vdc typical 36vdc * logic signal current: 7~16mA Typical 10mA * Pulse Input Frequency: 0~200kHz * Pulse Width: 2.
STEPPERONLINE CNC Stepper Motor Driver 1.0-4.2A 20-50VDC 1/128 Micro-step Resolutions for Nema 17 and 23 Stepper Motor #ad - 5μs * isolation resistance: 500mΩ * cooling: natural cooling or forced cooling * Environment: Avoid dust, oil fog and corrosive gases * Operating Temperature: -10℃~45℃ * Vibration: 10-55Hz / 015mm * weight: Approx. 210g 7.